-
How to transfer the data of AFG 1022 to transmits a waveform to the edit memory1?
DATA:DATA EMEMory1,#42000<DAB><DAB>...<DAB>
Hello,
I have no idea how to transfer the DBL data/floating data to above<DAB>, for example, if I want to transfer 3 points(3.141, 2.5, 3) to AFG1022,DATA:DATA EMEMory1,#40003<DAB><DAB>...<DAB>
ORDATA:DATA EMEMory1,#13<DAB><DAB>...<DAB>
Should I write?
and what is the DAB values should I send for 3.141, 2.5, 3 . I'm trying to write the command in LabVIEW. -
RE: Hardcopy command to save PNG file didn't work for TBS2000B
Hello Iris,
But HARDcopy commands work for transferring picture with the format of BMP. Usually we use this command is because we don't want an addtional USB device. It is ok for me to use SAVE:IMAge commnads on MSO2,4,5,6 series.
-
RE: Hardcopy command to save PNG file didn't work for TBS2000B
Hi Afonso,
We did set the format to the right one and got the *.png file, but the fact is that it is not a real picture with the format of PNG. it is a BMP file just seemed to be modified the extention name to PNG. The size of PNG file should not be about 1.1MB. -
RE: Hardcopy command to save PNG file didn't work for TBS2000B
It is mostly due to the file size. we don't expect to transfer the format once again due to the special time requirement. -
Hardcopy command to save PNG file didn't work for TBS2000B
Hello,
We found no matter we chose PNG or BMP for the hardcopy command. the transferred picture always seems to be BMP files.
I also try to update the firmware to the newest version. it is always the same.
the size for both of them are 1.1MB. just the file names are different. When openning the *.png file with photoshop, it could not be recognized.
could it be resolved soon? -
Messy code in the post content
Hi,
Messy code easily come out when editting the post, it really last for a long time, don't know what's wrong with it.
Microsoft Edge..
-
RE: LABVIEW software communicates with oscilloscope via USB
Hi Mr Zhou,
<a href="https://www.tek.com.cn/manual/oscilloscope/tbs2000b-series-oscilloscopes-tbs2000">TBS2000B Series Programmer Manual | Tektronix</a><br> <br> So how did you change the channel to channel2? Did you update the code to open and select channel2? <br> <br> Please refer to the Page 245 for the channel selection.<br> <br> Just a reminder, the LabVIEW demo is just for reference, it could not do everything what you want.<br>  you need to do the coding yourself.
-
RE: MSO44 memory and bandwidth questions
1. It is still 62.5M,
2. I have no idea about the theoretical speed. but the TekScope need about 1 minutes to finish the 4*31.25M acquisition. -
RE: Alternating Polarity Resistance/Resistivity Test of 6517B
I tried to measured a 1M Ohm resistor, the voltage is +-50V, 15S, and the current is 50uA, -50uA,50uA, -50uA,50uA, -50uA,50uA, -50uA,50uA, -50uA,50uA, -50uA...... so according to &#160;I calc=(I1+3(–I2) +3(I3) +(–I4))/8, the current&#160; Icalc is 50uA or -50uA.<br> <br> sorry, overlook the information in your reply above. this seems to be ok for me to do the calculation.<br> <code><em>1(I1) + 3(I2) + 3(I3) + 1(I4) all divided by 8. And the polarities of the current measurements are made to be all positive.</em></code><br> but it seems a bit different from the white pater -
RE: Alternating Polarity Resistance/Resistivity Test of 6517B
Hi Ty,
Thanks for the reply.
As describe in the document:
Note that not all of these currents are of the polarity that might be expected, given the polarity of the voltages applied (+, –, +, –).
Is it possible that the current to be a negagive value according to I calc=(I1+3(–I2) +3(I3) +(–I4))/8, and then how should we do with it?